How To Fix A Yeti Hopper Zipper?

If you have a Yeti Hopper zipper that doesn’t seem to be working right, there are a few simple steps that you can take to fix it.

First, remove the debris and dirt that may be clogging up the zipper. Then, use a toothbrush to clean out any built-up gunk inside of the zipper.

Finally, dry off the area and insert your key in the zipper to test it out. If everything seems to be working correctly, you can go ahead and reattach the zipper’s attachment clips.

Fix A Yeti Hopper Zipper

Source: Gearjunkie

How To Fix A Yeti Hopper Zipper

If you are experiencing difficulty zipping up your Yeti Hopper, there is a good chance that you can fix it. First of all, remove the hopper by unscrewing the four screws located at the top.

Once it has been removed, clean and lubricate the zipper with light oil or silicone grease. Finally, reattach the hopper by screwing it back in place.

Remove Hopper

If your Yeti Hopper zipper is not functioning correctly, there are a few steps you can take to rectify the situation. The easiest way to fix the zipper is by simply removing it from the hopper and replacing it with a new one.

However, if this does not work, there are other methods that may be necessary such as lubricating the tracks or using zip strips. Before taking any action, consult your Yeti Hopper manual for more information on how to fix the zipper.

If none of these solutions work, then you will need to replace the entire hopper unit. By following these simple steps, you can restore proper function to your Yeti Hopper zipper.

Clean And Lubricate Zipper

If your Yeti Hopper zipper is not functioning properly, it is important to clean and lubricate it as soon as possible. Cleaning the zipper can be done with a damp cloth and mild soap.

Once the zipper is clean, apply a light layer of silicone lubricant to the metal slides. Replace the slider if it needs to be replaced, and re-lubricate where necessary. Finally, make sure to close the zipper fully before using it again to avoid any issue down the road.

Reattach Hopper

If your Yeti Hopper zipper breaks, it is easy to fix by following these simple steps: First, locate the broken zipper and remove any remaining pieces of fabric.

Next, use a seam ripper to remove the stitches that hold the zipper together. After removing the stitches, gently press down on the seams so they are flat. Locate a new zipper and match up the edges before stitching them together using a needle and thread.

Once the new zipper is in place, trim off any excess fabric around it. Finally, repeat steps for the other side of the zipper.

What To Do If The Zipper Gets Stuck

If the zipper on your Yeti Hopper gets stuck, there are a few things you can do to fix it. Sometimes grease or dirt will get caught in the teeth of the zipper and cause it to become jammed.

You can try using a plunger to push down on the teeth of the zipper and force it open. If that doesn’t work, you can try spraying some WD-onto the teeth of the zipper and pushing down with your fingers.

Finally, if all else fails, you can take the hopper apart and clean both the slider and teeth of the zipper with a brush or a cloth soaked in alcohol. Once everything is cleaned up, you can reattach the hopper by following these instructions: first, put on gloves; then unscrew one side of the base; finally, screw on the side with gloves still on.

Be sure to test out your repaired Yeti Hopper before putting it back into use.

How To Fix If It Starts To Come Apart

If your Yeti Hopper zipper starts to come apart, follow these simple steps to fix it. Remove the zipper slider by gently pulling it out from the fabric of the bag.

Inspect the teeth on both sides of the slider for wear or damage. If there is significant wear or damage, replace the slider with a new one. Apply a thin layer of glue to the back of the slider and press it into place against the fabric.

Allow the glue to dry completely before reassembling your Yeti Hopper zipper.

How To Fix If The Hinges Are Broken

Fixing broken hopper zipper is same as fixing a Yeti cooler zipper. If your Yeti Hopper zipper is broken, there are a few simple steps you can take to fix it. Check to see if the slider is still attached to the zipper teeth by removing the screws that hold it in place.

If the slider isn’t attached, gently pull on both sides of the zipper until it comes off. Now you should be able to see where the slider moves up and down on the teeth – if it’s broken, replace it with a new one.

Reattach the screws and slide the slider back onto the teeth – make sure it’s positioned correctly before reattaching the plastic piece above it. Finally, reattach the tab above the slider and screw it into place – you’re done.

Conclusion

If your Yeti Hopper zipper is not functioning properly, there are a few things you can do to fix it: Check the teeth – make sure they’re not bent or broken.

Clean and lubricate the moving parts – including the slider, wheel, and tracks. Replace the zipper if necessary – it’s usually easy to do and only costs a few dollars.

Leave a Comment