How To Fix Puffer Jacket After Wash?

If you have an inflatable jacket that has been washed and dried, but it’s now puffed up and doesn’t seem to be holding its shape as well as it used to, here are a few tips on how to fix it.

Blow it out as much as possible: If you can get the air out of the jacket, it will help to keep it inflated. Apply a sealant: A sealant can help to keep the air from escaping and will also make the jacket less likely to stretch or sag over time.

Store it in a cool, dry place: If your jacket is stored in a warm, humid environment, it could eventually deflate. Don’t over-tighten the straps: Too much pressure might cause the fabric to tear or stretch, which would then ruin the jacket’s shape.

How To Fix Puffer Jacket After Wash

Source: nytimes

How To Fix Puffer Jacket After Wash

If you have a puffer jacket that has been washed recently, there are a few things that you can do to fix it. First, remove the wash clothes and check the fabric for wrinkles.

If there are any, trim them off with scissors. Next, apply a damp washing towel to the lower hem and center front of the jacket. Finally, start your machine and add hot water. Once the jacket is wet, remove the wash clothes and dry it off.

Remove Wash Clothes

If your puffer jacket has seen better days after a wash, follow these steps to fix it before it gets any worse: Begin by unzipping the jacket and removing the arms. Next, take off the collar and remove the buttons.

With all of the fabric separated, you can now start to fix any damages. Patch any tears or holes with fabric glue and then sew them closed using a zigzag stitch or bias tape if necessary. Once everything is patched, reattach the buttons and collar, and zip up the jacket for a finished product!

Check Puffer Jacket Fabric For Wrinkles

If you notice that your puffer jacket has begun to show wrinkles after being washed, don’t despair! There are a few simple steps that you can take to fix the issue. Start by checking the fabric for any signs of damage or abrasion.

If there are no visible signs of wear or damage, try ironing the fabric flat using a low heat setting. After ironing the fabric, use an adhesive spray to attach a piece of felt to the back of the jacket so it doesn’t wrinkle again when worn.

Finally, make sure to store your puffer jacket in a high-quality garment bag when not in use to prevent it from wrinkling further.

Trim Puffer Jacket Fabric If Necessary

If you notice that your puffer jacket fabric is starting to fray after several washes, it’s time to take action. To prevent the fabric from fraying, first try using a seam ripper or razor blade to cut away any loose threads.

If that doesn’t work, then use a needle and thread to sew the fabric back together. Finally, trim any excess fabric with scissors so there is no visible stitching. Follow these steps every time you wash your puffer jacket to keep it looking good for years to come.

Apply A Damp Washing Towel To Lower Hem And Center Front

If your puffer jacket has a lower hem and center front that are not staying down after being washed, try applying a damp washing towel to the area. The towel will help to keep the fabric in place while it dries.

Be sure to press the towel against the garment after applying it so that wrinkles are eliminated. Check the garment every few minutes until it is completely dry to ensure that no more wrinkles form. Repeat this process as needed if your puffer jacket does not stay put after being washed.

Be sure to follow the care instructions provided with your garment for best results. Use a light wash cycle and cold water when washing your puffer jacket for added protection against shrinkage or tears in the fabric. Avoid using fabric softeners or bleach when laundering your puffer jacket because they can damage it over time.

Hang your puffer jacket on a hanger after each wash to avoid stretching or tearing of the fabric.. . Enjoy wearing your newly laundered puffer jacket!

Start Washing Machine And Add Hot Water

If your puffer jacket has shrunk in the wash, follow these steps to fix it:

a. Add some cold water to the machine before starting it up.

b. Add the puffer jacket and start the machine according to the manufacturer’s instructions.

c. Put a washing bag on top of the jacket and fill it with cold water.

d. Close the lid of the washer and wait for the machine to finish its cycle.

Remove the jacket from the washer and hang it to dry. If you notice that your puffer jacket has no warmth after being washed, try adding some hot water to your machine instead of cold water when starting it up.

Some materials shrink more in hot than in cold water, so try adding hot water if you’re having trouble getting your puffer jacket to fit properly after being washed in cold water.

Hot water may help soften any fabric softener residue left in the garment, which can cause shrinkage or loss of shape during laundering. Adding a liquid detergent like All-Cladens may also help dissolve any residues and improve the overall performance of your garment during laundering cycles at home using cold or hot water temperatures as desired.

You can also put your puffer jacket into a mesh laundry bag before washing it to help suspend dirt and debris while washing without affecting color or shape retention over time (although this will not remove all residues). Hang your puffer jacket to dry completely after washing, since excessive heat may damage delicate fabrics over time.

Remove Wash Clothes And Dry Puffer Jacket

If your puffer jacket has shrunk after being washed, follow these steps to get it back to its original size: Remove the wash clothes from the puffer jacket and hang them to dry.

Once they’re dried, measure the circumference of the jacket around the bust area and compare it to your original measurements. If there is a significant difference in circumference, then you will need to purchase a new puffer jacket or alter the existing one.

If the circumference remains approximately the same, then you can proceed with following these instructions: Cut off any excess fabric around the bust area that was not originally cut according to your measurements. Sew this newly cut fabric up into a circle around the bust area, making sure that it is securely sewn down so that it doesn’t move during wear.

Make sure that you reinforce this seam by stitching another piece of fabric over it on either side for extra strength and durability. Now you are ready to wear your new puffer jacket!

Remove Zipper And Hood

When you are unable to remove the zipper and hood from your puffer jacket after washing, follow these simple steps. First, use a seam ripper to carefully cut around the zipper and hood.

Then, using a pair of scissors, cut through the fabric along the lines you made with the seam ripper. Finally, pull out the zipper and Hood piece by piece until it is free from the jacket.

Clean And Lube Seams

You can clean and lubricate your puffer jacket’s seams by following these simple steps: Soak the seam in warm water for about minutes before washing it. Use a mild soap to remove any dirt or debris.

Apply a light coat of lubricant to the affected area, and then wash the jacket as usual. To prevent the seam from fraying, finish by applying a protective sealant after each wash. Lubricants should be applied regularly to keep your jackets performing at their best, so make sure to have a bottle on hand!

Puffer jackets are typically resistant to harsh chemicals and detergents, but always test a small patch first before treating an entire garment.

Dry the jacket promptly after washing to avoid stretching or tearing the seams


Drying a puffer jacket after washing can be tricky, but with a little patience and some basic sewing skills, you’ll be able to fix most common Puffer Jacket Problems.

Leave a Comment

Your email address will not be published. Required fields are marked *